Use these tools to Treat
the metal after it is fired
Tumbler
for polishing silver 3 lb
(not a toy)
QTY $79.95
Liquid Burnishing Compound for tumbling
QTY 1qt $13.05
Shot, Stainless Steel For Tumblers Mixed per pound one should be enough
three is Max.
QTY $18.63
Tumbler Kit
Everything you need to start polishing silver. A tumbler, stainless
steel shot and 1 quart of burnishing solution.
QTY $111.63
for the tumbler Kit
Burnisher is used to smooth the silver by
hand, creates a mirror finish.
$12.40
Qty.
Qty.
Set of needle files $15.99
Qty.
Ring Mandrel $31.65 Well made lasts a lifetime.
Rawhide Mallet $19.95
QTY
For
use with Ring Mandrel, will not mar silver.
This ring has been oxidized in Liver of Sulfur,
which turns the silver black, then Polished. Wherever you can't buff up
stays black.
Qty. Oxidizer,
Liver of Sulfur One quart $9.75
A very soft brush that quickly removes the white
scale that covers PMC+ when it comes out of the kiln. Does not scratch
the silver.
Brass brush for polishing silver. $8.85
QTY
Cold Mold Silicon Rubber $31.75
QTY
This
revolutionary two-part compound cold-flows and does not require heat for
vulcanization. Knead equal parts of the A and B putties together, press
it around your pattern and cure at room temperature. The compound
has a 0% shrinkage rating and is self-lubricating; no release agents are
needed. You use all the putty so there's no waste! Cures in 30 minutes.
3M Sponge Sanding Pads $11.20
QTY
Great for working with PMC, sponge sanding pads from 3M are so flexible
that they conform to almost any contour or surface. Micron graded
abrasives make them safe for every stage of sanding and pre-polishing.
Pads can be used wet or dry for a wide variety of metal, model-making
and lapidary applications. These high-quality pads are made of
long-lasting, closed-cell foam rubber with permanently bonded aluminum
oxide abrasives. They will not gouge surfaces and the convenient, hand-
sized pads (41/2" x 5'/2") can be folded or trimmed to fit into detailed
areas.
Finishing Sheets Reduce finishing
steps! With 3M micron-graded abrasives, you remove a controlled amount
of material, leaving a more consistent finish after each grade of
abrasive.
Wet or Dry Tri-M-Ite Polishing Paper
Select this paper for interior shapes and for polishing just about any
contoured surface. Sheets measure 8 1/2" x 11 ". 400, 600, 1200, 4000,
6000, 8000 grit
(6 sheets two each)
$13.45
QTY
Grit Color
400 (coarsest) green
600 grey
1200 blue
4000 pink
6000 mint
8000 (finest) light green (1 Micron!)
For use as a
polishing compound on Silver, gold, Test on a small inconspicuous area
first stainless steel, brass, copper, aluminum, tin and other metals to
enhance shine and remove tarnish.
DO NOT USE ON: painted, coated, plated or layered metals.
CAUTION: This product may damage certain metals. Test on a sm
inconspicuous area first. There is a component in this product
that may wear down the metal overtime, especially bronze or gold
plated metals.
INSTRUCTlONS: Add a small amount of this product to a soft cloth and rub
into the metal. Once you are satisfied with the tarnish removal, use a
clean soft cloth to buff and remove residue from the surface of the
metal.
CAUTION: Do not use for anything other than directed. Long periods of
exposure may irritate sensitive skin, gloves should be worn in these
instances. With use on dinnerware, wash dishes after use with dish soap
to remove any residual compound before use. Keep out of reach of
children.
IF ACCIDENT OCCURS: If the compound is ingested; wash your mouth out
vith water thoroughly, and seek medical attention immediately. If the
compound comes in contact with the eyes DO NOT RUB. Rinse well with
clean water and seek immediate medical attention if irritation occurs.
Tumbler
for polishing silver 3 lb
(not a toy)
Qty.
Set of needle files $15.99 
For
use with Ring Mandrel, will not mar silver.
This ring has been oxidized in Liver of Sulfur,
which turns the silver black, then Polished. Wherever you can't buff up
stays black.
This
revolutionary two-part compound cold-flows and does not require heat for
vulcanization. Knead equal parts of the A and B putties together, press
it around your pattern and cure at room temperature. The compound
has a 0% shrinkage rating and is self-lubricating; no release agents are
needed. You use all the putty so there's no waste! Cures in 30 minutes.
